Jacuzzi Hot Tub Steam Enclosure User Manual

Steam Enclosure  
INSTALLATION INSTRUCTIONS  
R
BATH  
WHIRLPOOL  
 
1
 
Important: Read complete instructions before beginning installation.  
Remove the unit carefully from the carton. Retain the shipping carton until satisfactory inspection of the product has  
been made. Lay out and identify all parts using the installation instructions as reference. Check the carton for small  
hardware bags that tend to fall to the bottom of the carton.  
Handle the glass panels carefully and protect the edges. Safety tempered glass is very resistant to breakage, but  
it can be broken by banging the edges against a hard surface. Do not remove any protective devices until you are  
ready to install the glass panels as the sharp corners of the panels can damage tile and floor surfaces.  
Wear safety glasses whenever drilling or cutting. When drilling holes in ceramic tile or marble, use a center punch  
and hammer to carefully break the surface glaze so the drill can start without skidding.  
Tools required: Tape measure, Level, #2 Phillips screwdriver, flat bladed screwdriver, drill and 1/8", 7/32" drill bits  
and a hacksaw.  
Step 1  
Measure the wall to wall opening along the center of  
the bath rim. Use a hacksaw to cut the bath track 1/16"  
short of this dimension. Note: On some installations it  
may be necessary to file the ends of the track to match  
the wall conditions.  
MEASURE  
Step 2  
Press the four vinyl plugs into both ends of the bath  
track  
A
B
Step 3  
Center the bath track on the bath rim and mark its  
position. Note: Drain holes face the interior of the bath.  
A
CENTER TRACK ON RIM  
2
 
PLUMB EACH JAMB  
Step 4  
Position the wall jambs on each end of the bath track  
withnotchesinthebottomofthejambspressedsecurely  
overthebathtrack. Usealeveltoplumbeachwalljamb.  
Makeapencilmarkonthewallthrougheachoftheholes  
in the wall jamb. Remove all parts and drill the walls in  
the locations marked using an 1/8" diameter drill. In tile  
walls drill 7/32" diameter holes and insert plastic wall  
plugs.  
D
A
TO  
Step 5  
I
N
T
Apply a continuous bead of caulking on the bottom of  
the bath track vinyl. Carefully replace the bath track in  
the position marked in Step 3. Slide the two pieces of  
jamb vinyl into the jamb filler. Replace the wall jamb  
closest to the shower head. The jamb filler should be  
installed with the opening closest to the interior of the  
bath. (Thisinsuresmaximumwaterproofingbyposition-  
ing the interior glass panel closest to the shower head.)  
Attach the jamb and jamb filler to the wall with three #8  
x 1-1/2" truss head screws.  
E
RI  
OR  
OF  
B
A
T
F
H
G
H
Step 6  
Measure the wall to wall opening at the top of the  
mounted wall jamb. Cut the header 1/16" short of this  
measurement. Check the header for fit.  
MEASURE  
3
 
Step 7  
All units are equipped with safety tee-lock jambs.  
Wheninstalledproperlytheheaderispermanentlylocked  
to the jambs and cannot be accidently dislodged. Slide  
the safety lock of the remaining wall jamb and jamb filler  
intotheheader. Theroundedsurfaceoftheheadergoes  
to the exterior and the jamb filler should be positioned  
with the opening closet to the exterior of the wall jamb.  
Holding the header at an angle engage the opposite  
end onto the mounted wall jamb and press the wall jamb  
into position on the bath track. Attach to the wall per  
Step 4.  
TEE-LOCK  
I
D
I
D
A
J
Step 8  
Obscure glass panels are installed with the rough  
side of the glass to the exterior. Attach rollers to the  
interior panel (rough glass surface closest to the top fin)  
and the exterior (rough surface away from the top fin  
using four 8-32 x 3/8" hex head screws. Press four vinyl  
silencers into the slots in the fin on the bottom of both  
panels.  
K
J
ROUGH  
SURFACE  
EXTERIOR  
PANEL  
INTERIOR  
PANEL  
L
4
 
Step 9  
Peel protective backing from the four adhesive  
bumpers and stick to top and bottom of the panel recess  
in the wall jambs. Lift the interior panel into position with  
the rollers engaging the roller slot in the header and the  
bottom fin inserted into the interior slot of the bath track.  
Repeat for the exterior panel. The vertical vinyl wiper  
blade of the interior panel should seal against the  
exterior panel when both panels are in a closed position.  
Ifthepanelsarenotparalleltothewalljambs, remove  
thedoorsandadjusttherollersupordowntocompensate.  
Step 10  
Press the trim ring over the base of the four acrylic  
towel bar brackets and press the brackets into the ends  
ofthetowelbars. Attachtheassembledtowelbarstothe  
glass panels with four 10-24 x 7/8" truss head screws.  
Q
N
O
P
N
Q
O
Step 11  
Caulk the ends of the bath track and the interior  
surface of the wall jambs  
Step 12  
Clean your Steam Enclosure with a soft cloth and  
nonabrasive cleaner.  
5
 
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.  
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.  
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this  
type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.  
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.  
Jacuzzi Whirlpool Bath  
P.O. Box 702168, Dallas TX 75370-2168  
Service Support: (800) 288-4002  
©1996 Jacuzzi Whirlpool Bath J992000  
8/13/04  
Printed on Recycled Paper  
Printed in the U.S.A.  
 

Infinity Portable Speaker TSS 500 User Manual
IOGear Computer Drive GUH224 User Manual
JBL Home Theater System SCS160 User Manual
Jenn Air Range JGR8855 User Manual
JL Audio Car Speaker 94376 User Manual
JVC Speaker System UX G1 User Manual
Karcher Pressure Washer HD 10 25 S VEX User Manual
Kawasaki Cordless Saw 840328 User Manual
KEF Audio Speaker FLC 2003 User Manual
KitchenAid Cooktop 3186523 User Manual