Jacuzzi Indoor Furnishings EV77959 User Manual

Refresh  
Personal Hygiene System™  
OWNER’S MANUAL  
Round  
EU44959 — ROUND FRONT  
Elongated EV77959 — ELONGATED FRONT  
This manual contains important safety information.  
Please read carefully before product installation or use.  
EX93000 Refresh Installation Manual 10/06  
 
Before Installation  
Tools Needed  
Flat head screwdriver  
Universal wrench (included)  
Measuring tape  
Phillips head screwdriver  
NOTE: The included Universal Wrench will work for most applications. Depending on your toilet  
configuration, an adjustable wrench may also be needed.  
Alternate Mounting Hardware  
Some toilets may not provide adequate access to the seat mounting holes preventing proper  
installation of the Standard Mounting Hardware.  
In this case you will need to use the Alternate Mounting Hardware and follow the enclosed instructions.  
Check Water Supply Line  
Check the line that connects the toilet tank to the water shut-off valve. If it is rigid pipe, you may need  
to purchase a flexible hose to replace it before installing the Refresh Personal Hygiene System™. The  
length of the hose and the size of the connectors will vary.  
Installation  
CAUTION  
CAUTION  
Please read these carefully before installing the Refresh Personal Hygiene System™.  
Failure to do so could result in flooding, leaking, or damage to the Refresh Personal Hygiene System™.  
1) Remove Toilet Seat  
Steps may vary by type of seat.  
a) Lift hinge covers and use a screwdriver to  
remove the mounting bolts.  
b) Remove the toilet seat.  
1b  
1a  
2b  
2) Turn OFF Water and Flush Toilet  
You may wish to place a container under the  
tank to catch any leaking that could occur  
during installation.  
a) Turn water valve OFF completely. If the water valve  
does not shut OFF completely, STOP. Repair the  
water shut-off valve before proceeding.  
b) Flush the toilet to empty the tank.  
c) Disconnect water supply line from toilet tank.  
2a  
2c  
IMPORTANT: Do not continue without completing these  
steps! Failure to do so could result in flooding, leaking, or  
damage to the Refresh Personal Hygiene System™.  
3b  
3) Install Mounting Plate  
3a  
NOTE:These instructions are for Standard Mounting Hardware. See  
Alternate Mounting Hardware at the top of this page for further details.  
a) Place Mounting Plate over mounting holes, flat side down,  
curve toward the back of the toilet.  
b) Insert bolts through the Mounting Plate and finger  
tighten the wing nuts. Make sure the crush washer and  
Mounting Holes  
metal flat washer are put on in the correct order (see  
graphic).  
Crush Washer  
Metal Flat Washer  
EX93000 Refresh Installation Manual 10/06  
2
 
Installation (continued)  
3) Install Mounting Plate (continued)  
c) Adjust mounting plate so length (L) between the front of the toilet  
bowl and the back of the mounting plate is as follows:  
L
3c  
Round (EU44959):  
L=18¼" (465 mm)  
Elongated (EV77959): L=20½"(495 mm)  
d) Tighten Mounting Bolts with screwdriver until the mounting plate is  
securely fastened to the toilet.  
4) Connect T-Valve and Hoses  
NOTE: If your water supply line is rigid pipe,  
you may need to replace it before installing  
the Refresh Personal Hygiene System™.  
a) Install the T-Valve between the water supply line  
and the toilet tank.  
b) Place the Refresh on or beside the toilet and  
4b  
4a  
connect the Bidet Hose to the Refresh.  
IMPORTANT: Use wrench to tighten all  
T-Valve  
connections before continuing. Failure to  
do so could result in flooding, leaking, or  
damage to the Refresh Personal Hygiene  
System™. Do not overtighten!  
Bidet Hose  
5) Attach the Refresh  
Water Supply Line  
a) Slide the Refresh onto the mounting plate.  
You will hear aclickindicating the seat has  
been properly attached.  
Confirm that the seat switch is in full  
contact with the toilet bowl rim.  
To Release the Refresh:  
5
Unplug the power plug and turn the water  
supply valve OFF.  
Push the button located on the right corner  
of the seat and gently pull.  
Press to  
Release  
6) Turn ON Water & Connect Power  
CAUTION: Use only a grounded  
15 Amp GFCI outlet!  
6b  
a) Turn the water supply valve ON slowly.  
Ensure the connections are not leaking  
before continuing.  
CAUTION: Use only a  
grounded GFCI outlet!  
6a  
IMPORTANT! Make sure work area is dry  
and hands are dry before continuing.  
power  
b) Insert power plug into a grounded 15 Amp  
GFCI outlet. The blue power LED on the  
Refresh Display Panel will illuminate.  
power save  
seat heat  
seat sensor  
IMPORTANT! Make sure the power plug is  
removed and the water supply is shut-off  
before removing the Refresh.  
7
7) Battery Installation  
a) Remove battery cover from Remote Control  
and insert two (2) AAA batteries (included)  
as shown.  
b) Refasten battery cover with screw.  
EX93000 Refresh Installation Manual 10/06  
3
 
Installation (continued)  
8) Remote Control Installation  
a) Identify a location for the Remote Control that is visible and reachable from the  
toilet and that does not obstruct the IR signal.  
Depending on your wall type, you can install the screws directly or use anchor  
mounts (provided) as shown.  
b) If you prefer to not drill holes in your wall, you may use double sided foam  
tape to adhere bracket to wall. In this case, make sure to choose a tape with an  
adhesive that will not damage wall upon removal.  
9) Filling the Reservoir  
a) Place a plastic sheet (not provided) over the seat. Sit on the Refresh to activate the seat switch. Press one  
of the wash functions on the Remote Control. The reservoir will begin to fill. It will take between 5 and 10  
seconds for the reservoir to completely fill.  
When the reservoir is full the wash wand will extend and begin to spray. Push STOP to cancel the wash  
function. Remove the plastic sheet and discard.  
b) Your Refresh bidet seat is now ready for use! Refer to the Operation section of this manual for programming  
and operation instructions.  
Troubleshooting  
Issue  
Low water flow or  
pressure  
Solution  
Possible Causes  
1) Clogged filter  
1) Clean filter  
2) Twisted hose  
3) Household water pressure low  
2) Straighten hose  
3) Increase water pressure to Refresh  
1
2
3
4
5
6
7
8
9
Nozzles do not function  
properly  
1) Nozzles are dirty  
2) Clogged filter  
1) Clean the nozzles  
2) Clean the filters  
3) Adjust water pressure  
3) Water pressure is too low  
Nozzles fail to react  
Nozzles are dirty  
Clean nozzles  
Washing feature does not  
work or fails to spray  
1) User not properly seated  
2) Seat switch is not contacting toilet  
fixture properly  
1) Adjust your sitting position  
2) Make sure the seat switch is contacting  
toilet bowl rim (switch is in seat foot)  
Product shuts OFF  
during use  
1) Washing time exceeding 5 minutes  
2) Power failure  
1) Repeat cleaning function  
2) Check power and/or unplug the cord  
to reset  
Seat not heated  
Seat temperature set to OFF  
Reset heated seat temperature  
Water not heating  
Water temperature set to OFF  
Pulsating / Spa mode activated  
Reset heated water temperature  
Reset to normal washing mode  
Water flow sporadic or  
inconsitent  
Dryer not working  
Dryer only operates when activated  
by weight of person on seat  
Sit on Refresh to operate Dryer  
EX93000 Refresh Installation Manual 10/06  
4
 
Operation  
Some features of the Refresh Personal Hygiene System™ are designed to function only when the seat is occupied.  
REMOTE CONTROL PANEL  
WARM WATER WASH  
INDICATOR LIGHTS  
Posterior (Rear)  
Cleansing  
Feminine (Vaginal)  
Cleansing  
power  
Water Temperature  
Low>Med>High>Off  
power save  
seat heat  
LCD Panel  
Seat Temperature  
Low>Med>High>Off  
seat sensor  
Warm Air Dryer  
On  
Low>Med>High  
AUXILIARY CONTROLS  
Powersave  
Function  
(backup for Remote)  
Decrease  
Increase  
AUX Stop  
AUX Wash  
Water Pressure  
Adjustment  
Stop  
(for Wash and Dryer)  
Using the Refresh Remote Control  
Warm Water Washing  
Sit on the seat and press the FRONT or BACK (either HIM or HER) button to begin water  
flow. Press STOP button to discontinue water flow.  
Water Flow/Pressure Adjustment  
While water is flowing, press the button to increase pressure or the  
LCD Panel  
button to decrease pressure. Repeat until desired pressure is reached. There  
are five (5) levels of water pressure. Each wider bar on the LCD graphic  
display represents one level increase.  
Pulsating Water Mode  
To change to Pulsating Mode;While water is flowing, press the FRONT or BACK (either HIM or HER) button for over  
three (3) seconds. To deactivate and return to normal washing mode, repeat the above step.  
Warm Air Dryer  
Press the WARM AIR button to start dryer. Press STOP to stop the dryer.  
Adjusting Seat,Water, and Dryer Temperature  
You must be sitting on the seat for these functions. The last entered temperature settings are stored in memory.  
View of  
LCD Panel  
Adjusting Seat Temperature  
Press SEAT TEMP button to adjust temperature. Repeat until desired level is achieved. There are  
four (4) temperature levels:low>medium>high>off. Each wider bar on the LCD graphic display  
represents one level increase. No LCD graphic indicates seat heating is OFF.  
Adjusting Water Temperature  
Press WATER TEMP button to adjust temperature. Repeat until desired level is achieved. There are  
four (4) temperature levels:low>medium>high>off. Each wider bar on the LCD graphic display  
represents one level increase. No LCD graphic indicates water heating is OFF.  
Adjusting Dryer Temperature  
Press WARM AIR button to adjust temperature. Repeat until desired level is achieved. There are three  
(3) temperature levels:low>medium>high. Each wider bar on the LCD graphic display represents  
one level increase.  
EX93000 Refresh Installation Manual 10/06  
5
 
Operation (continued)  
Setting the Clock  
a) Press and hold the STOP button on the remote Control for over 5 seconds until the Clock flashes.  
b) Use the button to set the HOUR and the button to set the MINUTES.  
Power Save Mode  
The Refresh Personal Hygiene System™ includes a power saving feature to reduce electrical  
consumption when not in use. Once set, the Power save function turns the Refresh ON and OFF each  
day according to your programmed time settings.  
Setting the Power save Start and End Times  
a) Press and hold the Power save button for 5 seconds. “POWER SAVE STARTon the  
Remote and the Power save LED on the Refresh will flash.  
b) Adjust the Power save Start time using the WATER FLOW button to set the HOUR  
and the WATER FLOW button to set the MINUTES. When the desired Start time is  
displayed on the Remote, press the Power save button again.  
c) “POWER SAVE ENDon the Remote and the Power save LED on the Refresh will flash.  
d) Adjust the Power save End time using the WATER FLOW button to set the HOUR  
and the WATER FLOW button to set the MINUTES. When the desired End time is  
displayed on the Remote, press the Power save button again.  
The remote LCD will show“POWER SAVE ON”and the Power save LED on the Refresh will be green. Power  
save function is now ON and the unit will go into Power save mode at the programmed start time.  
power  
Enabling and Disabling the Power save  
a) Press the Power save button to toggle between Power save ON and Power save OFF.  
power save  
seat heat  
b) To change Power save Start and End Times refer to the procedure above.  
seat sensor  
When Power save is Operating  
a) When the Refresh is in Power save mode, the Power save LED on the seat will glow ORANGE.  
b) Sitting on the Refresh while it is in Power save mode returns the unit to normal operation. The Refresh will  
not re-enter the Power save mode until the next day’s scheduled start time.  
Auxiliary Controls  
AUXILIARY CONTROLS  
(backup for Remote)  
There are two (2) buttons on the rear, right corner of the  
Refresh for use when the Remote Control is unavailable.  
AUX Stop  
AUX Wash  
Rear Wash: Sit on the seat and press the AUX WASH button  
to begin water flow (only posterior cleaning is available when using Auxiliary Controls).  
(For each of the operations below you must start in the Rear Wash mode.)  
Water Pressure: Press the AUX WASH button again until the desired water pressure is achieved. Press the AUX  
STOP button to discontinue the water flow.  
Warm Air Dryer: Press the AUX STOP button to activate Warm Air Dryer. It will automatically be set to the  
medium temperature level. Press the AUX STOP button again to turn OFF the dryer.  
Seat Temperature: To adjust the Seat Temperature, press and hold the AUX STOP button for more than 5  
seconds. Press the AUX STOP button again to change seat temperature:low>medium>high>off.  
Water Temperature: To adjust the Water Temperature, press and hold the AUX WASH button for more than 5  
seconds. Press the AUX WASH button again to change water temperature:low>medium>high>off.  
Remote Control Beeping/Silent Modes  
The remote control has two (2) operational modes:Beeping Mode and Silent Mode. Beeping mode  
beeps to confirm when a command from the remote has successfully been received by the seat.  
To change modes, press and hold the WATER TEMP button on the remote for 5 seconds.  
EX93000 Refresh Installation Manual 10/06  
6
 
Maintenance  
CAUTION  
CAUTION  
Always unplug the Refresh before cleaning!  
Seat Cleaning and Removal  
Use a soft, damp cloth and mild cleanser (such as  
dish soap) to wipe down the seat. DO NOT scrub  
or use harsh, abrasive products to clean the Refresh  
bidet seat.  
For a more thorough cleaning, you may remove  
the Refresh bidet seat. To release, push the button  
located on the back right side of the seat and pull  
the Refresh bidet seat forward.  
Press to  
Release  
Nozzle Cleaning  
It is recommended that you clean the retractable nozzles monthly or as necessary.  
To clean the nozzles, pull them out gently and use a soft, damp brush or cloth to  
wipe down. DO NOT use soap or detergents to clean nozzles.  
Filter Cleaning  
For proper Refresh bidet seat function, it is important to occasionally clean the water filter. Frequency  
of cleaning depends on your local water supply. Clogged filters cause decreased water flow, affecting  
operation. Remove filters by hand. DO NOT operate with filters removed.  
T-VALVE FILTER:  
BIDET-HOSE FILTER:  
1
2
1
3
5
2
4
6
1) Turn water supply valve OFF  
completely.  
2) Flush toilet to empty the water  
tank. (Failure to do so could result  
in leaking or flooding!)  
1) Turn water supply valve OFF  
completely.  
2) Flush toilet to empty the water  
tank. (Failure to do so could result  
in leaking or flooding!)  
3) Disconnect the Bidet Hose from  
the Refresh.  
3
5
4
6
3) Unscrew the filter from the T-Valve.  
(the end not connected to a hose)  
4) Gently brush and clean the filter  
with water to remove build-up.  
4) Gently brush and clean the filter  
with water to remove build-up.  
5) Reconnect the Bidet Hose to the  
Refresh.  
5) Reconnect the filter to the T-Valve.  
6) Turn the water supply back ON  
6) Turn the water supply back ON  
and check for leaks.  
and check for leaks.  
For other issues or q1ue-s8ti0on0s-,2co8n8ta-c4t J0a0cu2zzi Customer Service:  
Contact Information  
Warranty  
Jacuzzi Whirlpool Bath  
Customer Service  
14801 Quorum Dr., Suite 400  
Dallas,TX 75254  
The Refresh Personal Hygiene System™ is covered by  
a limited one year warranty, valid from the original  
date of purchase for original purchaser.  
Please complete and return the enclosed product  
registration card to receive important product  
updates.  
PHONE:  
WEB:  
1-800-288-4002  
EX93000 Refresh Installation Manual 10/06  
7
 

Indesit Freezer BA 13 GF User Manual
Integra CD Player DPC 75 User Manual
Intel Computer Hardware IB957 User Manual
Invacare Camping Equipment MA80 User Manual
Jacuzzi Hot Tub DZ95 User Manual
JVC VCR HR A43U HR A63U User Manual
Kathrein Satellite TV System UFE 370 S User Manual
Kenmore Water Heater 153320392 HT User Manual
Kenwood Mixer MX310 series User Manual
KitchenAid Microwave Oven KHHC2090SSS User Manual