Jacuzzi Indoor Furnishings Faucet Kit User Manual

Water Rainbow™ Fill Spout/Faucet Kit  
Installation Instructions  
IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements.  
TheWaterRainbowllspout/faucetkitisdesigned  
for installation on most Jacuzzi Whirlpool Bath  
products or on any bath having sufcient rim space  
WATER RAINBOW FILL SPOUT  
AND FAUCET HANDLES  
for mounting. The installation procedure requires  
drilling holes in the bath shell, mounting ttings,  
and making the proper water supply connections  
to the faucet valves and ll spout. Hole drilling  
templates and instructions are provided here for  
this purpose.  
Contents of Kit: Water Rainbow ll spout as-  
sembly, faucet handles with inserts--hot (red dot)  
and cold (blue dot), faucet valve assembly (2),  
1/4-20 x 1-1/2" hex bolt with/washer and locknut  
(2), 1-1/2" diameter. push-on speednut (2), faucet  
handle gasket (2), #10-24 x 3/8" PHPM screw (2),  
1/4" MIN.  
cartridge valve wrench with instructions.  
RIM  
Preparation  
Locate the area on the bath or spa rim where  
the Water Rainbow and faucet valves are to be  
installed. For separated valve installations, refer to  
illustrations B and G; for paired valve installations,  
refer to illustrations C and H.  
INSIDE OF  
BATH  
LOCATE FILL SPOUT  
ON TOP OF BATH  
RIM TO ALLOW  
Forinstallationonallbaths,locatetheWaterRain-  
bow ll spout and valves on a level surface which  
will allow water to clear the rim and ow directly into  
the bath (see illustration A). Also be certain the ll  
spout has easy access and that there is adequate  
space for plumbing connections to the ll spout,  
both before and after installation. (Refer to plumb-  
ing instructions regarding top access installation,  
illustration M.)  
DIRECT WATER  
FLOW INTO BATH  
A
HOLE FOR FILL SPOUT  
HOT WATER  
COLD WATER  
FAUCET HOLE  
B
1-1/2" DIA.  
FAUCET HOLE  
2-1/2"  
2-1/2"  
1-1/2" DIA.  
1/2"  
15/64" DIA.  
9/32" DIA.  
15/64" DIA.  
9/32" DIA.  
1/2"  
11/16"  
15/64" DIA.  
15/64" DIA.  
15/64" DIA.  
1-3/8" DIA.  
15/64" DIA.  
15/64" DIA.  
7"  
7"  
Dry t the Water Rainbow ll spout and valves in  
the desired area (before drilling holes) to be sure  
the location is appropriate.  
INTERIOR OF  
BATH OR SPA  
HOLE DRILLING SCHEME FOR WATER RAINBOW  
SPOUT AND FAUCETS - SEPERATE VALVE CONFIGURATION  
Drilling Holes  
Detach the templates (on back page) and tape  
them onto the acrylic surface of the bath rim, lo-  
cating the center lines of the ll spout and valve  
holes according to appropriate dimensions given  
in Illustration B or C.  
HOLE FOR  
FAUCET  
HOLES  
C
FILL SPOUT  
2-1/2"  
HOT  
COLD  
1-1/2" DIA.  
1-1/2" DIA.  
1/2"  
1/2"  
15-64"  
15/64" DIA.  
11/16"  
15/64"  
3"  
9/32" DIA.  
1-3/8" DIA.  
2-1/2"  
9/32" DIA.  
7"  
Note: To insure template has been printed to  
scale, measure the 2 1/2" spacing from center  
Fill Spout mark and 9/32" hole mark for the 1/4  
- 20 Hex Bolt anchors.  
15/64" DIA.  
INTERIOR OF  
BATH OR SPA  
HOLE DRILLING SCHEME FOR WATER RAINBOW  
SPOUT AND FAUCETS - PAIRED VALVE CONFIGURATION  
Jacuzzi Whirlpool Bath  
6683000G  
8/06  
 
SCREW #10-24 X3/8" PHPM (2)  
SUGGESTED WATER RAINBOW  
PLUMBING SCHEME A - FOR  
SEPARATED VALVE  
INSERT  
FAUCET HANDLE  
(HOT)  
WATER RAINBOW  
FILL SPOUT  
CONFIGURATIONS  
(Pipe and fittings not provided.)  
GASKET  
FAUCET HANDLE (2)  
INSERT  
FAUCET HANDLE  
(COLD)  
LOCKNUT  
1/4-20 (2)  
VALVE (2)  
WASHER  
FAUCET HANDLE (2)  
FAUCET WRENCH  
1/4" FLAT (2)  
5/8" X 1/2"  
ELL  
BOLT  
1/4-20 X 1-1/2"  
HEX HEAD  
HOT WATER  
SUPPLY  
5/8" O.D.  
COPPER PIPE  
TEE 5/8" X 5/8" X 1/2"  
SPEEDNUT  
PUSH-ON 1-1/2" (2)  
5/8" O.D.  
COPPER PIPE  
5/8" X 1/2"  
ELL  
COLD WATER  
SUPPLY  
G
WATER RAINBOW  
FILL SPOUT  
SUGGESTED WATER RAINBOW  
PLUMBING SCHEME B - FOR  
PAIRED VALVE CONFIGURATIONS  
(Pipe and fittings not provided.)  
INSERT  
FAUCET HANDLE  
(HOT)  
LOCKNUT  
1/4-20 (2)  
WASHER  
1/4" FLAT (2)  
FAUCET  
INSERT FAUCET HANDLE  
(COLD)  
HANDLE (2)  
SCREW #10-24 X3/8" PHPM (2)  
GASKET  
5/8" O.D.  
BOLT  
FAUCET HANDLE (2)  
COPPER PIPE  
1/4-20 X 1-1/2"  
HEX HEAD  
FAUCET WRENCH  
VALVE (2)  
5/8" X 1/2"  
ELL  
5/8" O.D.  
COPPER PIPE  
TEE 5/8" X 5/8" X 1/2"  
SPEEDNUT  
PUSH-ON 1-1/2" (2)  
HOT WATER  
SUPPLY  
5/8" X 1/2"  
ELL  
COLD WATER  
SUPPLY  
H
Jacuzzi Whirlpool Bath  
6683000G  
8/06  
 
Installing the Faucet Handles  
Install the rubber gasket into the faucet handle  
aligning the at of the gasket with the projection  
fromthehandle,thenaligningtheatsurfaceonthe  
stem with the at inside handle, place the handle  
onto the stem of the faucet valve.  
Insert the #10-24 x 3/8" L stainless steel PHPM  
screw (provided) through the handle and gasket  
into the valve stem and tighten.  
INSERT  
SCREW  
FAUCET  
HANDLE  
Rotate handles clockwise to the end of travel.  
Pushininsertswithdotsorientedtowardtheouter  
edge of the bath rim, red dot indicating hot water  
and blue dot indicating cold water. The notch in  
the insert must align with the ribs on the inside of  
the handles for ush engagement. (See illustra-  
tion I.)  
RUBBER  
GASKET  
VALVE STEM  
FAUCET HANDLE ASSEMBLY  
I
Plumbing Connections  
Note: Turn off water at main shut-off valve before  
making plumbing connections to supply lines.  
Connect the water line from the hot and cold valve  
to the threaded pipe extension of the ll spout per  
illustration G or H. Use Teon tape or thread seal-  
ant designed for use on plastics. Do not use oil  
base thread compounds.  
OPTIONAL SHOWER HEAD  
(NOT SUPPLIED)  
TRANSFER VALVE  
(NOT SUPPLIED)  
For bath ll spout only applications, refer to the  
suggested plumbing schemes G for separated  
valves and H for paired valves. If a rim or wall  
mounted shower is installed, a transfer or mixer  
valve will be required. Three variations are shown  
in illustration J (standard shower), K (rim mounted  
or hand held), and L(shower with anti-siphon valve  
if required by code.  
If local plumbing codes require the installation of  
an anti-siphon valve, locate the anti-siphon valve  
6" above the rim of the bath in a vertical position  
over a waterproof surface or xture to allow for  
any possible water leakage through the air vent.  
The valve must be exposed and have access for  
service.  
COLD WATER  
HOT WATER  
SUPPLY  
SUPPLY  
J
HAND HELD SHOWER  
(NOT SUPPLIED)  
TRANSFER VALVE  
(NOT SUPPLIED)  
Operation  
Checkforproperoperationofthellspout. Always  
llthebathwithamixtureofhotandcoldwater. Wa-  
ter temperatures in excess of 140° F may damage  
the ll spout and/or discolor the bath's surface.  
HOT WATER  
SUPPLY  
COLD WATER  
SUPPLY  
K
Jacuzzi Whirlpool Bath  
6683000G  
8/06  
 
Installation for Top Access  
OPTIONAL SHOWER HEAD  
(NOT SUPPLIED)  
If service access to Water Rainbow plumbing  
under the rim is not possible, it is possible to install  
the spout so that it can be replaced at a later date  
(if necessary) from the top of the rim. To do this,  
allow at least 2" of exibility in the piping so it can  
be pulled up through the rim. Use a compression  
tting or union at the connection of the pipe exten-  
sion to allow disconnection without rotating the ll  
spout. If a compression tting is not used, make  
sure there is a space of at least 6" from the back  
of the Water Rainbow to the wall, so the spout can  
be rotated to unscrew it from the piping. (See il-  
lustration M.)  
ANTI-SIPHON VALVE SHOULD  
BE A MINIMUM OF 6" ABOVE  
RIM OF BATH  
ANTI-SIPHON VALVE  
& TRANSFER VALVE  
(NOT SUPPLIED)  
6"  
To remove the ll spout from the top of the bath,  
rst pry off the cover. Do not use sharp tools!  
Then remove the two larger screws and pull the  
spout up.  
COLD WATER  
SUPPLY  
L
HOT WATER  
SUPPLY  
ALLOW 6" TO ROTATE  
Faucet Valve Replacement  
FILL SPOUT FOR REMOVAL  
Jacuzzi Whirlpool Bath has provided a special  
wrench with which to change the cylinder valve  
assembly under the water supply handles should  
it require replacement. Keep this tool in a safe  
place for use at a later date. To replace the cylinder  
valve and the seat assembly, rst turn off the water  
supply, then pry the insert from the square handle.  
Next,removethePhillipsscrewsecuringthehandle  
and remove the handle. Place the wrench on the  
bonnet and turn it counterclockwise. Next, remove  
the bonnet, leaving it in the wrench.  
ALLOW AT LEAST 2" OF  
FLEXABILITY IN PLUMBING  
TO LIFT FILL SPOUT  
WALL  
COMPRESSION  
FITTING  
BATH  
RIM  
Note the position of the valve cylinder stop before  
removing the cylinder. Now use pliers to pull the  
valve cylinder stem out of the body, then slip the  
replacement cylinder unit into the body so that  
stops of both faucets are positioned downward,  
toward the bottom of the bath allowing rotation in  
the same direction.  
Secure the bonnet in place with the wrench. Re-  
place the handle and the screw. Snap the insert  
into place. (See illustration N.) The above faucet  
replacement parts are available from your Jacuzzi  
Whirlpool Bath dealer.  
INSTALLING THE WATER RAINBOW  
WITH TOP ACCESS  
M
BODY  
ALIGN NOTCH  
WITH PROJECTIONS  
BONNET  
WRENCH  
SPRING  
SEAT  
VALVE  
CYLINDER  
GASKET  
HANDLE  
SCREW  
INSERT  
N
FAUCET ASSEMBLY  
Jacuzzi Whirlpool Bath  
6683000G  
8/06  
 
CAUTION  
Since plumbing ttings may contribute detectable amounts of lead to water, the following notice is required by California law  
(Proposition 65). "This product contains a chemical known to the State of California to cause birth defects or reproductive harm."  
In normal use, any lead exposure can be minimized by allowing the water to run free for several seconds before drinking.  
Proper installation of the ll spout and compliance with local codes is the responsibility of the installer. Jacuzzi Whirlpool Bath does  
not warrant connections of water supply ttings and piping, ll systems, or drain/overow systems. Nor is it responsible for damage  
to the bath (or spa) which occurs during any installation procedure.  
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.  
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.  
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of  
this type. It is the responsibility of the installer/owner to determine specic local code compliance prior to installation of the  
product.  
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.  
Jacuzzi Whirlpool Bath  
14801 Quorum Dr., Dallas TX 75254  
Customer Service: Call (800) 288-4002  
© Copyright 1991 Jacuzzi Whirlpool Bath 6683000G 8/06  
Printed in the U.S.A.  
Printed on Recycled Paper  
 
HOLE DRILLING TEMPLATE—WATER RAINBOW™  
CHECK TEMPLATE SCALE USING  
REFERENCE DIMENSIONS BEFORE DRILLING  
If scale is off, do not continue, call customer support at 1-800-288-4002 to obtain a new template  
BATH RIM  
HOLE FOR THREADED  
PIPE EXTENSION  
9/32" DIA.  
(FILL SPOUT)  
1-3/8" DIA.  
(2-1/2" REF)  
(1/2" REF)  
9/32" DIA.  
C
L
15/64"  
PILOT  
HOLE  
(2-1/2" REF)  
DRILL PILOT HOLE FIRST  
INTERIOR OF BATH  
HOT WATER  
FAUCET HOLE  
COLD WATER  
FAUCET HOLE  
(3" REF)  
1-1/2" DIA.  
1-1/2" DIA.  
15/64"  
15/64"  
RIB HOLE  
RIB HOLE  
15/64"  
PILOT  
HOLE  
15/64"  
PILOT  
HOLE  
DRILL PILOT HOLES  
AND RIB HOLES  
15/64"  
15/64"  
BEFORE DRILLING  
1-1/2" DIA. HOLE  
RIB HOLE  
RIB HOLE  
INTERIOR OF BATH  
Jacuzzi Whirlpool Bath  
6683000G  
8/06  
 
© Copyright 1991 Jacuzzi Whirlpool Bath 6683000G 8/06  
 

Kawai Musical Instrument CN290 User Manual
KEF Audio Speaker System KIT100 User Manual
Kensington Car Satellite Radio System 110V n 275W User Manual
KitchenAid Double Oven KEMS308S User Manual
KitchenAid Food Processor KFC3511 User Manual
KitchenAid Garbage Disposal KCDB250S1 User Manual
KitchenAid Gas Heater 710 0003 User Manual
KitchenAid Ice Maker KUIS185EWH0 User Manual
KitchenAid Oven KESK901SBL06 User Manual
Klipsch Speaker IC SW 8 T 2 User Manual